Body Transporters & Trays
Carrier Chassis
Call us at 800-410-0100 for a Quote
-
- Designed to lay flat for dressing procedures and/or tilt for embalming procedures.
- A handle is provided that when lifted tilts the platform and automatically engages the positive locking brake-leg mechanism.
- The subframe shape permits the simple lifting on or off of the operating platform, no mechanical fastening devices are required.
- Allows for easy access and removal of the tray with a cadaver lift.
-
- Fabricated of strong .12 tubing thickness, 1in/2cm. square tubing. Sub assemblies are of welded construction.
- Subframe is shaped to fit into the hitech plastic operating platform.
- (4) 8in/20cm swivel wheels, (2) with brake mechanisms.
- Cadaver lift accessible.
600009 - Bariatric Carrier Chassis
Call us at 800-410-0100 for a Quote
-
- Designed for use with oversize cases; Every facility should have at least one of these units available for these extreme situations.
- Top tray is permanently attached and fabricated from 12 gauge stainless steel.
- Carrier is designed with a 3 in./7 cm. permanent slope.
-
- 1.5 in./3 cm. square, .12 in tubing thickness, 304 stainless steel base frame.
- Stainless steel has a grained finish and all welds are polished to match.
- Support gussets are included on the base frame for added tray support.
- 8 in./20 cm. casters all with brake mechanisms.
-
- Total caster locking system.
- Custom elevating working heights.
- Rear hand crank elevation .
- Custom tray sizes.
600010 - Stretcher/Cadaver Carrier
Call us at 800-410-0100 for a Quote
-
- Designed for multi-purpose use in hospitals, coroner's facilities and mortuaries.
- Durable and economical, stainless steel body transporter.
- Top tray is permanently attached and fabricated from 16 gauge stainless steel.
-
- 1.5in/3cm squared stainless steel tubing vertical end rails. 1in/2cm crossrails.
- Heliarc welded for added strength and durability.
- Top is bolted to lower frame to allow for removal, yet remains sturdy while in use.
- 8in/20cm casters all with brake mechanisms.
- Heavy-duty rubber bumpers at each corner.
-
- Custom working heights, or adjustable height.
- Custom tray sizes.
- full side bumpers.
- Total caster locking system.
600015 - Standard Autopsy Carrier with Stainless Steel Tray
Call us at 800-410-0100 for a Quote
-
- Economically priced yet still perform well under heavy duty use.
- Cadaver lift accessible.
-
- 1.5in/3cm square, .12in tubing thickness, 304 stainless steel base frame.
- Stainless steel has a grained finish and all welds match adjoining surfaces.
- 8in/20cm casters all with brake mechanisms.
-
- Tilt crank.
- Front and rear crank control.
- Total caster locking system.
600038 - Autopsy Carrier w/ Rollers
Call us at 800-410-0100 for a Quote
-
- These units are designed as an integral part of the Total Roll System for easy loading and unloading of cadavers.
- Designed to minimize manual cadaver handling .
- Economically priced yet still performs well under heavy duty use.
- Cadaver lift accessible.
- Carriers will hold: T3626 Series Trays.
-
- (10) Nylon maintenance free rollers.
- Flip latch to hold tray while in transport.
- Fabricated with a permanent slope of 2in/5cm.
- 1.5in/3cm square, .12in tubing thickness, 304 stainless steel base frame.
- Stainless steel has a grained finish and all welds are polished to match.
- 8in/20cm casters all with brake mechanisms.
-
- 600038-C Rear Elevating Crank
- 600038-TL Total Locking Casters System
- 600038-FRC Front and Rear Elevation Crank
- 600038-H Stryker Hydraulic Unit
600015-C - Hand Crank Autopsy Carriers
Call us at 800-410-0100 for a Quote
-
- Comes with a hand cranking system to assist in some elevation to benefit working comfort and allow for drainage of overflow liquids and debris.
- Economically priced yet still performs well under heavy duty use.
- Cadaver lift accessible.
-
- 1.5in/3cm square, .12in tubing thickness, 304 stainless steel base frame.
- Stainless steel has a grained finish and all welds are polished to match.
- 8in/20cm casters all with brake mechanisms.
600015-FRC - Front & Rear Elevating Autopsy Carriers
Call us at 800-410-0100 for a Quote
-
- Comes with a front and rear hand cranking system to assist in elevation to benefit working comfort and allow for drainage of overflow liquids and debris.
- Economically priced yet still performs well under heavy duty use.
- Cadaver lift accessible.
-
- 1.5in/3cm square, .12in tubing thickness, 304 stainless steel base frame.
- Stainless steel has a grained finish and all welds are polished to match.
- 8in/20cm casters all with brake mechanisms.
- Front and rear hand cranking lifting system.
Autopsy Carrier with Scale
Call us at 800-410-0100 for a Quote
-
- 1.5 in./3 cm. square, .12 in. tubing thickness, 304 stainless steel vertical end rails.
- Stainless steel has a grained finish and all welds match adjoining surfaces.
- Permanent slope of 1.5 in./3 cm.
- 8 in./20 cm. casters all with brake mechanisms.
- Easy push button controls (Hold/Print, Units, Tare, On/Off/Zero).
- Units of measure - lb., kg., lb./oz.
- System includes 4 PB loadcells.
- FULL FCC compliance, UL/CUL power adapter, CE, WEEE directive.
Click here to view or download this item in our online catalog!
600014 - C-Arm Accessible Autopsy Carrier
Call us at 800-410-0100 for a Quote
-
- Designed specifically for use with c-arm style x-ray machines.
- Open frame construction allows the c-arm clear travel nearly the entire length of the carrier.
- The carrier accommodates our x-ray type autopsy tray, allowing the case to remain on one tray for both the x-ray and autopsy procedures.
- Fabricated from 1.5in/3cm square, .12 tubing thickness, 304 stainless steel tubing.
-
- Top tray holder fabricated from 1in./2cm. stainless steel tubing.
- Stainless steel has a grained finish and all welds match adjoining surfaces.
- 8in/20cm casters all with brake mechanisms.
- Designed with a permanent slope of 3in/5cm.
- Cadaver lift accessible.
C-Arm Lateral Access Autopsy Carrier
Call us at 800-410-0100 for a Quote
-
- Designed specifically for use with c-arm style x-ray machines.
- Laterally open frame construction allows the c-arm clear travel nearly the entire length of the carrier.
- The carrier accommodates our x-ray type autopsy tray, allowing the case to remain on one tray for both the x-ray and autopsy procedures.
- Fabricated from 2in/3cm x 3in/7cm, .12 tubing thickness, 304 stainless steel tubing.
-
- Top tray holder fabricated from 1in./2cm. stainless steel tubing.
- Stainless steel has a grained finish and all welds match adjoining surfaces.
- 6in/15cm casters all with brake mechanisms.
- Designed with a permanent slope of 2in/5cm.
- Cadaver lift accessible.
T3626-HS Standard Body Tray
Call us at 800-410-0100 for a Quote
-
- Fabricated with hand slots and without a drain hole.
- Inside corners finished smooth for easy cleaning.
-
- Includes drain plug to prevent fluid loss in transport or while racking and stored.
- All exposed welds are ground and polished to match adjoining surfaces.
-
- Laboratory stopper #9 for use without adapter.
Stainless Steel Autopsy Tray
Call us at 800-410-0100 for a Quote
-
- Fabricated from 14 gauge 304 stainless steel with No. 4 finish.
- Detachable top ensures a secure fit with no mechanical fastening devices required.
-
- Includes drain plug to prevent fluid loss in transport or while racking and stored.
- Angled interior long sides for easier body transfer.
- Depressed pattern for easier drainage.
-
- Laboratory stopper #9 for use without adapter.
Stainless Steel Autopsy Tray with Trough
Call us at 800-410-0100 for a Quote
-
- Fabricated with a perimeter trough which allows fluid to flow away from the body and down the sides of the platform toward the drain.
- Fabricated from 14 gauge 304 stainless steel with No. 4 finish.
-
- Includes drain plug to prevent fluid loss in transport or while racking and stored.
- All exposed welds are ground and polished to match adjoining surfaces.
-
- Laboratory stopper #9 for use without adapter.
Click here to view or download this item in our online catalog!
Molded Plastic Carrier Chassis Tray
Call us at 800-410-0100 for a Quote
-
- Fabricated of hi-tech molded, fire retardant plastic.
- Shaped to fit the subframe of the carrier chassis.
- X-rays can be taken without the removal of the cadaver from the autopsy table.
-
- Includes drain plug to prevent fluid loss in transport or while racking and stored.
- Detachable plastic top ensures a secure fit with no mechanical fastening devices required.
- Top of platform is formed with ribs to promote drainage to the gutters.
- Reinforced bottom structure enables easy mobility from rack to chassis through use of a cadaver lift.
-
- Drain adapter assembly M764 with lab stopper 5.5.
- Drain hose with hose clamp (sold in foot increments).
- Laboratory stopper #9 for use without adapter.
Stainless Steel Flat Storage Tray
Call us at 800-410-0100 for a Quote
-
- Fabricated from 16 gauge tray with 14 gauge understructure providing extra strength.
- Tray completely flat for easy body transfer.
- For use with our Cadaver Storage System.
-
- Design load: 300 lbs.
- All edges welded for extra strength.
- For use with storage racks that have support arms spread a maximum of 42 in. / 106 cm.
-
- Available in two sizes: 24 in. & 30 in. width.
Fiberglass Tray
Call us at 800-410-0100 for a Quote
-
- Fiberglass platform designed for use as an autopsy carrier or various racking system.
- X-rays can be taken without the removal of the cadaver from the autopsy table, when combined with a proper carrier.
- Minimum order of (5) units for all fiberglass tray orders.
-
- Includes drain plug to prevent fluid loss in transport or while racking and stored.
- Reinforced bottom structure enables easy mobility from rack to chassis through use of a cadaver lift.
- Trays can be ordered with or without ribs, designed for easy drainage.
- Trays can be ordered with or without x-ray slides.
-
- X-ray slide guides for holding x-ray cartridge.
- Drain adapter assembly M764 with lab stopper 5.5.
- Drain hose with hose clamp (sold in foot increments).
- Laboratory stopper #9 for use without adapter.
Storage Board
Call us at 800-410-0100 for a Quote
-
- Designed as an economical body storage tray for use with our cadaver storage system.
- Rubber moulding around full perimeter.
-
- For use with storage racks having support arms spread a maximum of 42in/106cm.
- .75in/1cm thick plywood. Laminated top, protective coating on bottom.
- Weight capacity will vary depending on storage application.
Transfer Board
Call us at 800-410-0100 for a Quote
-
- Designed for use with mortuary refrigerators and storage racks with full width roller assemblies.
- Provides a stable platform for use with cremation containers or shrouded cadavers.
- Can also be used for body transfers from removal cots.
-
- Fabricated with eight hand slots.
- All edges rounded.
- Machined from high density polyethylene.
- Weight capacity will vary depending on storage application.
First Call Mortuary Cot
Call us at 800-410-0100 for a Quote
-
- A cot designed to be highly maneuverable in close quarters, providing easy access to the body.
- Folding end section shortens the cot by 15". Combined with its tapered head section, navigating corners becomes much less of an obstruction.
- Multi-level undercarriage provides flexibility upon retrieval.
-
- (1) model 375 1" burgundy mattress.
- (2) model 430 burgundy, 5' two-piece quick release restraint straps.
- (4) swivel wheels. Load end can be locked when necessary.
- Available with sidearms, please inquire.
- See image for available accessories.
Roll-In Mortuary Cot
Call us at 800-410-0100 for a Quote
-
- Extra long wheel base to provide exceptional stability.
- Slide action leg lock; securely lock both legs simultaneously when folded.
- Able to be used as a wheeled stretcher itself and/or is also wide enough to accommodate a portable stretcher.
-
- (1) model 372 1" burgundy mattress.
- (2) model 430 burgundy, 5' two-piece quick release restraint straps.
- Stair glides that reduce wear on the cot and promote smooth movement down stairs.
- See image for available accessories.
Multi-Level Mortuary Cot
Call us at 800-410-0100 for a Quote
-
- Designed to enable a single person to perform retrieval. Special release levers make it possible to raise and lower the cot without assuming the full weight of the cot and body.
- Compatible with high floor vehicles. The legs unfold and lock automatically during unloading, and refold again promptly when loaded into any vehicle.
- Multi-level feature allows the body to be moved from bed to cot.
- Wide enough to accommodate a portable stretcher.
- Acts as a highly maneuverable, two-wheeled stretcher when the undercarriage is folded and locked.
-
- (1) model 372 1" burgundy mattress.
- (2) model 430 burgundy, 5' two-piece quick release restraint straps.
- Built in stair guides that reduce wear on the cot and promote smooth movement down stairs.
- See image for available accessories.
Bariatric Mortuary Cot
Call us at 800-410-0100 for a Quote
-
- A cot designed to transport bodies up to 1,000 lbs.
- Independent leg design allows the front legs to fold/unfold, while the rear legs (operator's end) remain engaged to carry the cot's weight into the vehicle.
- Additional design versatility allows use of the loading wheels to move cot in the vertical position.
- Dual release handles for both front and back legs allow for one-person loading and unloading.
- Allows for easy maneuverability in tight areas and down stairs.
-
- Powder coated, heavy-duty frame weighing only 75 lbs.
- 6" wheels. Swiveling operator end and Fixed load end.
- Unique, independent leg design and wide (25.5") surface for increased stability.
- Scuff strips protect the finish.
- Height adjusts to seven different positions.
- Mattress clips hold mattress in place and make cleaning easier.
-
- Large side rails for additional security.
- Side lift handles to provide additional lifting points for heavier cases.
- Extra large first call cover designed for large cases.
- See image for available accessories.
Side-by-Side Bariatric Mortuary Cot
Call us at 800-410-0100 for a Quote
-
- A cot designed to handle large bodies, yet still maintain the ability to be placed side-by-side in the rear of most vehicles.
- Handles large bodies with ease a the narrow bed-surface provides increased maneuverability.
-
- (1) 1' mattress.
- (2) seven-foot two-piece black restraints.
- Compatible with most of our covers and pouches.
- See image for available accessories.
600015-H Hydraulic Autopsy Carrier
Call us at 800-410-0100 for a Quote
-
- Multi-functional hydraulic carrier designed for hospitals, coroner's facilities and mortuaries.
- Durable and economical stainless steel adjustable height body transporter.
- Hydraulic base with height adjustment via foot pedal.
-
- 1.5 in./3 cm. square, .12 in. tubing thickness, 304 stainless steel vertical end rails.
- Heliarc welded for added strength and durability.
- 8 in./20 cm. casters all with brake mechanisms. Brake will lock instantly with a single foot pedal.
- Solid surface base allows for easy cleaning.
- Designed for use with our T3614 & T3615 Stainless Steel Cadaver Trays.
Click here to view or download this item in our online catalog!
600017-H Hydraulic Autopsy Carrier
Call us at 800-410-0100 for a Quote
-
- Multi-functional hydraulic carrier designed for hospitals, coroner's facilities and mortuaries.
- Durable and economical stainless steel adjustable height body transporter.
- Hydraulic base with height adjustment via foot pedal.
-
- 1.5 in./3 cm. square, .12 in. tubing thickness, 304 stainless steel vertical end rails.
- Heliarc welded for added strength and durability.
- 8 in./20 cm. casters all with brake mechanisms. Brake will lock instantly with a single foot pedal.
- Solid surface base allows for easy cleaning.
- Designed for use with the T3603 Molded Plastic Carrier Chassis Trays
Click here to view or download this item in our online catalog!
600018-H Hydraulic Autopsy Carriers
Call us at 800-410-0100 for a Quote
-
- Multi-functional hydraulic carrier designed for hospitals, coroner's facilities and mortuaries.
- Durable and economical stainless steel adjustable height body transporter.
- Hydraulic base with height adjustment via foot pedal.
-
- 1.5 in./3 cm. square, .12 in. tubing thickness, 304 stainless steel vertical end rails.
- Heliarc welded for added strength and durability.
- 8 in./20 cm. casters all with brake mechanisms. Brake will lock instantly with a single foot pedal.
- Solid surface base allows for easy cleaning.
- Designed for use with our T3626 Stainless Steel Cadaver Trays.
Click here to view or download this item in our online catalog!
600018 - Autopsy Carrier
Call us at 800-410-0100 for a Quote
-
- Economically priced yet still performs well under heavy duty use
- Uniquely designed for use with the Series T3626 Standard Body Tray
- Cadaver lift accessible
-
- 1.5in/3cm square, .12in tubing thickness, 304 stainless steel base frame.
- Fabricated from 1.5 in./3 cm. square .12 tubing thickness, 304 stainless steel tubing
- Top tray holder fabricated from 11 gauge, .120 thickness, 304 stainless steel sheet flanged for strength
- Stainless steel has a grained finish and all welds match adjoining surfaces
- 8 in./20 cm. casters, all with brake mechanism
-
- 600018-TL Total Locking Caster System (Permanent slope of 1.5 in./3 cm.)
- 600018-C Carrier with Rear Elevation (Adjustable up 6 in./15 cm.)
- 600018-FRC Carrier with Front & Rear Elevation (Adjustable up 6 in./15 cm.)
- 600018-H Carrier with Hydraulic Front & Rear Elevation (Adjustable up 13 in./33 cm.)
600017 - Standard Autopsy Carrier with Molded Plastic Carrier Chassis Trays
Call us at 800-410-0100 for a Quote
-
Designed for use with a T3603 or T3604 Molded Plastic Carrier Chassis Trays. This autopsy carrier is economically priced yet it still performs well under heavy duty use.
- Cadaver lift accessible.
-
- Fabricated from 1.5 in., .12 tubing thickness, 304 stainless steel tubing
- Top tray holder fabricated from 1 in. stainless steel tubing
- Stainless steel has a grained finish and all welds match adjoining surfaces
- 8 in. casters all with brake mechanisms
-
- Total Locking Caster System
- Rear Elevation
- Front and Rear Elevation with Crank Control
- Hydraulic base with height adjustment via foot pedal
